亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

limit position hydraulic cylinder Sold to Malaysia

Release time:2023-11-12 15:29:31 Hits: Current position: Home > News

This article mainly introduces:

Malaysia hydraulic cylinder,limit position hydraulic cylinder manufacturer,limit position hydraulic cylinder

Malaysia limit position hydraulic cylinder

(Malaysia limit position hydraulic cylinder,produced by Hengyu Group)

limit position hydraulic cylinder are widely used in Malaysia,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed limit position hydraulic cylinder for customers from Malaysia.

Introduction to limit position hydraulic cylinder:

The limit position hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the limit position hydraulic cylinder, bite. Elimination method: When installing the limit position hydraulic cylinder, ensure that the axis position of the limit position hydraulic cylinder is consistent with the direction of movement; Make the load borne by the limit position hydraulic cylinder as far as possible through the limit position hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

When the limit position hydraulic cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the limit position hydraulic cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

When the limit position hydraulic cylinder is kept, do not pay attention to keeping the oil port open, which will produce the condition of accepting foreign bodies at all times, which is absolutely not allowed. Storage must be filled with anti-rust oil or working oil, and plug.

If the limit position hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the limit position hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow limit position hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the limit position hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the limit position hydraulic cylinder includes the leakage caused by excessive wear of the limit position hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and limit position hydraulic cylinder, and the phenomenon of "pulling the limit position hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about limit position hydraulic cylinder:

How does the variable amplitude cylinder work?
The variable amplitude cylinder is generally an engineering hydraulic cylinder connected by the front and back earrings, and the telescopic expansion of the hydraulic cylinder changes the Angle of the arm of the lifting machinery to achieve the role of the variable amplitude, according to the role it plays is called the variable amplitude cylinder, and there is no variable amplitude hydraulic cylinder in the classification of hydraulic cylinders.

Why can't the hydraulic cylinder be replaced with water?
Hydraulic oil for hydraulic transmission has a variety of requirements for viscosity, density, flow rate, and temperature, which are not available for water.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲永久精品国产来久精品| 日韩久久精品一区二区三区介绍| 久久99热精品首页| 日韩推理片电影在线播放| 18禁强伦姧人妻又大又久久| 欧洲日韩在线观看一区二区三区视频| 亚洲人妻一区二区久久| 久久国产无码模特视频| 在线视频精品福利91| 久久熟女av一区二区三区| 久久久久久久久久久久久久久久久久久| 人与嘼一区二区三区| 欧美亚洲专区一区二区| 东北乱国产对白刺激视频| 在线播放亚洲欧美日韩| 亚洲国产精品国揄产拍| 亚洲欧美国产其他二区| 精品久久久久精品三级18| 超碰人人在线免费观看| 久久久精品视频地址| 亚洲精品一区二区三区中文字幕| 有码无码人妻一区二区| 麻豆理论片在线观看| 2021久久国自产拍精品| 在线精品国产一区二区三区| 日本阿v不卡在线观看视频| 国产日韩欧美久久综合网| 亚洲91精品视频在线观看| 99亚洲国产精品18久久| 中文字幕日韩电影在线| 亚洲中文字幕国产综合| 欧美日韩激情精品久久久久久| 亚洲区一区二区三区视频| 久久久精品熟女亚洲av麻豆| 亚洲综合色婷婷久久| 亚洲伦理精品国产成人一区| 亚洲欧洲一区二区三区av| 亚洲色无码专区在线观看精品| 免费看中文字幕一级高清| 在线国产精品一区二区三区| 国产精品23一区二区|