亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

double acting cylinder Sold to Ethiopia

Release time:2023-11-12 15:30:37 Hits: Current position: Home > News

This article mainly introduces:

Ethiopia hydraulic cylinder,double acting cylinder manufacturer,double acting cylinder

Ethiopia double acting cylinder

(Ethiopia double acting cylinder,produced by Hengyu Hydraulic Cylinder Factory)

double acting cylinder are widely used in Ethiopia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed double acting cylinder for customers from Ethiopia.

Introduction to double acting cylinder:

The wear of the hard chromium plating layer of the double acting cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

After chrome plating of the piston rod of the double acting cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

The repair method of the double acting cylinder: the repair of the double acting cylinder must use brush plating. This is because this repair method can be carried out on site, and the repair effect is good. In this way, loading and transportation can be eliminated to shorten the repair time and improve work efficiency. In addition, the coating obtained by brush plating has good binding force and will not have obvious boundaries. Moreover, the repair surface has high hardness and good wear resistance.

The double acting cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the double acting cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The double acting cylinder is basically composed of double acting cylinder and double acting cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

Answers to some questions about double acting cylinder:

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美人与性动交b欧美精品| 精品免费福利片国产| 视频一区二区三区日韩视频| 国产熟女视频一区二区三区| 久久久久久久 亚洲精品| 这里只有久久精品| 男人吃奶大鸡巴操逼视频| 大鸡吧视频在线观看| 欧美一区亚洲一区视频在线观看| 青娱乐极品视觉导航| 久久久三级黄片免费视频| 国产老妇伦国产熟女91| 久久久国产了楼凤| 大吊肏子宫在线观看| 裸体美女被操的啊啊直叫| 日韩人妻无码中字一区二区| 无码人妻丰满熟妇区精品| 骚货 淫水 国产| 午夜福利国产三级片| 国产高清第一区第二区第一页| 国产中文字幕在线一区二区三区| 国产高清乱码女大生AV| 操女人真人大骚逼| 插插插插插插插插插插插| 中文字幕欧美中日韩精品| 中文无码av动作片| 日韩欧美中文字幕国产精品| 欧美va精品亚洲va精品| 国产精品你懂的在线资源| 国产91视频观看| 大鸡巴插入阴道视频| 中文字幕一区二区 在线| 欧美亚洲熟妇视频在线观看| 几巴怪物操逼视频| 亚洲福利小视频在线观看| 鸡巴操骚逼视频播放| 从后面狠狠的干白嫩少妇| 泡芙啪啪啪黄色污污| 久操视频中文字幕在线观看| 国产成人亚洲欧美久久| 大鸡插骚货人人色|