亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

500 tons hydraulic press cylinder Sold to Ethiopia

Release time:2023-11-12 15:32:08 Hits: Current position: Home > News

This article mainly introduces:

Ethiopia hydraulic cylinder,500 tons hydraulic press cylinder manufacturer,500 tons hydraulic press cylinder

Ethiopia 500 tons hydraulic press cylinder

(Ethiopia 500 tons hydraulic press cylinder,produced by Hengyu Hydraulic Cylinder Factory)

500 tons hydraulic press cylinder are widely used in Ethiopia,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed 500 tons hydraulic press cylinder for customers from Ethiopia.

Introduction to 500 tons hydraulic press cylinder:

Analysis of commonly used seals: The wear ring and slip ring commonly used on the 500 tons hydraulic press cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

The definition of the minimum starting pressure of the 500 tons hydraulic press cylinder refers to the minimum working pressure of the 500 tons hydraulic press cylinder in the no-load state, which is a comprehensive index reflecting the manufacturing and assembly accuracy of the 500 tons hydraulic press cylinder parts and the size of the sealing friction.

The coordination of the sliding parts of the 500 tons hydraulic press cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

After chrome plating of the piston rod of the 500 tons hydraulic press cylinder, the surface flatness is not fully treated: After chrome plating of the piston rod surface, the method of post-plating polishing should be changed to post-plating polishing. Although it is necessary to increase the thickness of the coating before grinding (generally increased by about 0.02 in the diameter direction), it can remove chrome plating defects well, and test the binding force of the coating. In addition, due to the micro-roughness of the grinding surface, the trough can store lubricating oil, which can improve the wear resistance and extend the service life.

Answers to some questions about 500 tons hydraulic press cylinder:

How to store hydraulic cylinder?
After cleaning the hydraulic cylinder with diesel or kerosene, apply lubricating oil and wrap it in oil paper, preferably in a wooden box, and store it in a dry and non-corrosive environment. The outer surface and inner surface of the hydraulic cylinder are sprayed with diesel oil, and the inner layer is covered with cloth and the outer coating of anti-rust oil is good. Put it in a dry place, clean it with diesel oil, and then apply a layer of anti-rust inside and outside the butter.

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产一区二区与亚洲av| 人妻互换免费中文字幕| 久久久成人国产精品麻豆| 日本一区二区三区中文字幕八戒视频| 日韩精品一区二区亚洲v欧美v日韩| 国产又大又长又粗又猛视频| 亚洲av成为人一区二区| 欧美亚洲另类在线第一页| 久久久久久99国产精品免费| 人与嘼一区二区三区| 在线播放亚洲欧美日韩| 欧美成人3p视频在线观看| 久久秘一区二区三区| 国产精品欧美大片在线观看| 国产欧美精品区一区二区三区竹菊| 亚洲国产精品久久久久av| 免费看亚洲精品大片| 欧美亚洲一区二区成人| 日韩精品一区二区三区在线| 亚洲mm视频网站在线播放| 亚洲色无码专区在线观看精品| 亚洲精品电影一区二区三区| 日本在线一区二区免费| 国产精品久久久久九九九九不卡| 国产成人亚洲综合91精品首页| 在线国产精品一区二区三区| 成人一级片黄色一级片| 国产成人欧美日本在线观看| 2017中文字幕在线| 久久久久国产精品熟女影院| 国产日韩欧美精品小视频| 亚洲成人情色综合网| 97精品国产自产在线观看| 日韩欧美精品中文字幕一区| 欧美激情国产精品视频一区| 久久熟女av一区二区三区| 日本成人在线不卡视频| 日本电影三级一区二区三区| 亚洲综合色婷婷久久| 国产三级黄色片观看| 国产性夜夜春夜夜爽夜夜|