亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Uzbekistan

Release time:2023-11-16 08:45:04 Hits:107 Current position: Home > News

This article mainly introduces:

Uzbekistan hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Uzbekistan synchronous hydraulic cylinder

(Uzbekistan synchronous hydraulic cylinder,produced by Hengyu Group)

synchronous hydraulic cylinder are widely used in Uzbekistan,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed synchronous hydraulic cylinder for customers from Uzbekistan.

Introduction to synchronous hydraulic cylinder:

synchronous hydraulic cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the synchronous hydraulic cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

synchronous hydraulic cylinder piston rod material introduction: In general, we use 45 steel to produce synchronous hydraulic cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

Improve the service life of the synchronous hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the synchronous hydraulic cylinder (such as the synchronous hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the synchronous hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the synchronous hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single synchronous hydraulic cylinder exhaust.

synchronous hydraulic cylinder installation precautions: Before installing the synchronous hydraulic cylinder into the system, the parameters on the synchronous hydraulic cylinder label should be compared with the parameters when ordering. The base of the synchronous hydraulic cylinder must have sufficient stiffness, otherwise the synchronous hydraulic cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

Answers to some questions about synchronous hydraulic cylinder:

Hydraulic cylinder load algorithm?
If it is thrust, load = working pressure x piston area. If it is pulling force, load = working pressure x(piston area - piston rod area).

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美亚洲综合中文字幕蜜桃成熟| 久久久久久久性生活| 日本午夜免费福利视频| 日韩熟女精品一区二区三区| 国产精品国产三级在线| 欧美激情国产精品视频一区| 韩漫漫画在线免费看视频| 日韩精品一区二区三区高清免费| 99久久免费精品国产免费高清| 久久免费少妇高潮视频| 国产精品23一区二区| 色狠狠av一区二区三区香蕉| 呻吟丰满一区二区三区| 日韩欧美一区中文字幕在线| 91蜜臀综合99国产区| 人妻精品一区二区三区| 亚洲综合色婷婷久久| 久久久区一区二区三| 亚洲永久精品国产来久精品| 一区二区三区欧美激情| 波多野结衣av一区二区| 久久久久久999一区二区三区| 国产99青草视频在线播放视| 一区二区日韩av激情| 国产综合精品久久久久成人蜜臀| 国产精品久久小视频| 欧美精品专区一区二区| 精品无码中文字幕在线| 欧美精品专区一区二区| 亚洲gv永久无码天堂网| 国产在线观看一区视频| 欧美日韩国产成人精品自拍视频| 亚洲岛国av一区二区| 中文字幕熟女一区二区三区| 国产精品久久小视频| 苍井空一区二区三区在线观看| 国产美女高潮抽搐流水在线看| 国产精品不卡在线视频| 好看的福利电影在线| 西野翔人妻中文字幕电影| 韩国爱情电影年轻的母亲|