亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

folding machine cylinder Sold to Australia

Release time:2023-11-19 14:07:01 Hits: Current position: Home > News

This article mainly introduces:

Australia hydraulic cylinder,folding machine cylinder manufacturer,folding machine cylinder

Australia folding machine cylinder

(Australia folding machine cylinder,produced by Hengyu Group)

folding machine cylinder are widely used in Australia,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed folding machine cylinder for customers from Australia.

Introduction to folding machine cylinder:

The folding machine cylinder should be vented: when the folding machine cylinder is installed or parked for a long time to work again, the air will penetrate into the folding machine cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the folding machine cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the folding machine cylinder, the oil is best entered and discharged from the highest point of the folding machine cylinder. folding machine cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When the initial action of the folding machine cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the folding machine cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

folding machine cylinder is the most important part of construction machinery, the traditional processing method is: broaching folding machine cylinder block - fine boring folding machine cylinder block - grinding folding machine cylinder block. The rolling method is: broaching folding machine cylinder block - fine boring folding machine cylinder block - rolling folding machine cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the folding machine cylinder block is about 1-2 days, rolling 1 meter of the folding machine cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the folding machine cylinder increases by 25%. If the folding machine cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality folding machine cylinders, you must take the rolling production process. After the folding machine cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

The pressure of the sliding surface of the folding machine cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the folding machine cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Answers to some questions about folding machine cylinder:

What is a hydraulic cylinder assembly?
Assembly, which means aggregate. A series of parts or products, formed to achieve a specific function of the whole, the general term for this system is assembly. The hydraulic cylinder assembly is not a single hydraulic cylinder part, which can be used by connecting the hydraulic hose.

Why is there noise in the hydraulic cylinder of the excavator lift arm?
There is no noise of a normal cylinder, check whether the throttle is ringing, or the mechanical part connected with it is ringing, and the mechanical part can be greased. If it can't be ruled out, disconnect the cylinder from the mechanical part and act alone to see what the situation is.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久久久久99国产精品免费| 国产精品午夜福利在线观看| 国产精品久久久久九九九九不卡| 九色九九综合久久爱| 国产精品综合久久久久久| 中文精品久久久久国产网址| 欧美日本一道本一区二区三区| 无码人妻w在线视频影院| 日韩一区二区人妻9999| 在线无码中文强乱爆乳系列| 国语自产精品视频二区在线| 国产一区二区日本在线观看| 日韩在线中文字幕观看| 国产精品久久久久久福利69| 99久久免费精品国产免费高清| 午夜无码精品一区二区三区| 波多野结衣av一区二区| 91久久久久久波多野高潮| 国产又大又长又粗又猛视频| 精品国产日本一区二区| 五月天丁香花婷婷色| 久久久久久国产综合精品| 欧美高清手机一区二区| 国产精品亚洲欧美日韩一区在线| 欧美精品精品一区乱| 国产人成尤物在线免费观看| 一区二区日韩av激情| 91狠狠人妻久久久久久综合| 日本动漫精品v毛片大全| 中文字幕日韩在线高清欧美| 国产又长有粗的视频| 欧美日韩成人精品久久久| 亚洲av成为人一区二区| 日本欧美一区二区免费不卡| 亚洲av乱码一区二区三区女| 国产精品热门在线播放| 日韩一区二区合集影院在线观看| 天天干天天射天天日天天操| 国产永久免费观看的黄网站| 亚洲精品在线观看日本国产| 日韩免费码中文字幕在线|