亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reset cylinder Sold to Thailand

Release time:2023-11-23 08:22:58 Hits: Current position: Home > News

This article mainly introduces:

Thailand hydraulic cylinder,reset cylinder manufacturer,reset cylinder

Thailand reset cylinder

(Thailand reset cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reset cylinder are widely used in Thailand,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed reset cylinder for customers from Thailand.

Introduction to reset cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

If the seal of the reset cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and reset cylinder, and the phenomenon of "pulling the reset cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

The pressure of the sliding surface of the reset cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the reset cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the reset cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Answers to some questions about reset cylinder:

What is the pressure provided for a 63-bore cylinder with a pressure of 2 mpa?
2 mpa pressure is equivalent to 20 kg per square centimeter, 6.3 cm straight longitude, 3.15 cm radius, square, multiplied by, calculated an area of about 31.5 square centimeters, multiplied by 20 kg, the pressure is about 630 kg.

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲欧洲日本精品| 巨屌抽插舔阴视频| 草草久性色av综合av| 我要看成人免费毛片| 男人的天堂日本在线观看| 男人扒开女人腿狂躁免费| 欧美成人3p视频| 看小伙草白女人比的黄片| 美女插逼插出淫水来| 亚洲AV无码一区二区三区系列| 把美女日到高潮喷水视频| 鸡巴插骚逼视频欧美风格| 免费黄片视频星空| 亚洲女同一区二区三久久精品| 99热这里有精品在线观看| 国产精品久久一区二区三区动| 中文字幕乱码人妻一区二区三区| 制服丝袜国产在线第一页| 毛片日产av一区二区三区四区| 少妇精品久久久一区二区免费| 夫妻性生活在线免费视频| 欧美人与动人物A级| 大鸡巴干浪穴视频| av在线国产哟哟| 日国产精品1卡二卡三卡| 在线观看日韩欧美| 色哟哟精品视频一区二区| 精品一区二区视频在线观看| 日韩欧美一区二三区风间由美| 三级片成人京东热五月天| 亚洲波多野结衣日韩在线| 日本乱人伦中文在线播放| 中日韩VA无码中文字幕| 骚逼被操视频拳交| 伊人久久久久久久久香港| 大男人在线无码直播| 韩国精品视频一区二区在线观看| 久操视频中文字幕在线观看| 一级做a爱过程免费视频俩| 思思夜免费公开视频| 成人黄色精品久久app|