亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

200 ton hydraulic cylinder Sold to Austria

Release time:2023-11-30 10:59:51 Hits: Current position: Home > News

This article mainly introduces:

Austria hydraulic cylinder,200 ton hydraulic cylinder manufacturer,200 ton hydraulic cylinder

Austria 200 ton hydraulic cylinder

(Austria 200 ton hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

200 ton hydraulic cylinder are widely used in Austria,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed 200 ton hydraulic cylinder for customers from Austria.

Introduction to 200 ton hydraulic cylinder:

200 ton hydraulic cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the 200 ton hydraulic cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

When the 200 ton hydraulic cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the 200 ton hydraulic cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

200 ton hydraulic cylinder body inspection: The inner surface of the 200 ton hydraulic cylinder and the piston seal are the main factors causing the leakage in the 200 ton hydraulic cylinder, if the 200 ton hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the 200 ton hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

200 ton hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching 200 ton hydraulic cylinder block - fine boring 200 ton hydraulic cylinder block - grinding 200 ton hydraulic cylinder block. The rolling method is: broaching 200 ton hydraulic cylinder block - fine boring 200 ton hydraulic cylinder block - rolling 200 ton hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the 200 ton hydraulic cylinder block is about 1-2 days, rolling 1 meter of the 200 ton hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the 200 ton hydraulic cylinder increases by 25%. If the 200 ton hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality 200 ton hydraulic cylinders, you must take the rolling production process. After the 200 ton hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

Answers to some questions about 200 ton hydraulic cylinder:

The inner diameter of the injection cylinder is 203.2mm and the diameter of the screw is 63.5mm. What is the enhancement ratio?
Oil pressure multiplied by the cross-sectional area of the cylinder is equal to the theoretical output force value, and then multiplied by the efficiency of the cylinder is equal to the actual output force value, and the oil pressure can be calculated by inverting the value input.

Does the excavator use a hydraulic cylinder?
First, construction machinery is generally a hydraulic cylinder. Second, hydraulic transmission equipment is usually composed of four components, power, execution, control and auxiliary. And the hydraulic cylinder as a linear reciprocating motion or less than 360. Reciprocating motion of the hydraulic mechanism, simple structure, reliable work, is also widely used in the hydraulic system of the main actuator, it is the prime mover in the form of mechanical energy to drive the hydraulic pump produced by the liquid pressure energy, and then can be directly driven load for reciprocating movement or less than 360.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
黄色视频网在线观看| 爱爱视频小抽插动漫| 欧美人人做人人爽人人喊| 9亚洲导航深夜福利亚洲| 日韩有码视频在线| 青春草在线视频观看| 亚洲大尺度无码无码专线一区| 大鸡吧老外操中国逼| 国产裸模大尺度私拍视频| 亚洲男性天堂一区二区三区| 男人和女人干污污| 东京热无码AV一区二区三区| 留学生美女被大黑屌猛戳| 免费黄片视频星空| 亚洲一区二区三区日本在线| 日本高清一区二区三区在线观看| 国产无圣光一区福利二区| 亚洲av 又黄又爽十大| 亚洲男人的天堂2021| 中日美女毛5片一区二区三区| 男生鸡鸡插进女生笑穴里| 国产伦精品一区二区三区视频抖音| 另类亚洲欧美专区第一页| 那种视频在线观看你懂的| 99久久久国产精品美女| 黄色三极片在线观看| 日韩 欧美 成人 免费| 尤物性生活午夜在线视频| 精品久久久久五月婷五月| 国产一区二区在线观看精品| 国内揄拍国内精品| 亚洲综合一区国产精品| 欧美日韩国产这里只有精品| 澳门一区二区免费下线观看| 国产精品白浆一区二区三区| 黑丝美女被操到高潮| 午夜精品在线视频| 美国女人抠插bbb| 啊啊不要你那痛死爽死了直播一区| 国产精品视频美熟女一区二区| 把女生操出水的视频|