亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

reciprocating cylinder Sold to Pakistan

Release time:2023-12-12 10:13:48 Hits: Current position: Home > News

This article mainly introduces:

Pakistan hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

Pakistan reciprocating cylinder

(Pakistan reciprocating cylinder,produced by Hengyu Hydraulic Cylinder Factory)

reciprocating cylinder are widely used in Pakistan,because of no need for deceleration device,long service life,smooth movement.So our company has designed reciprocating cylinder for customers from Pakistan.

Introduction to reciprocating cylinder:

reciprocating cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the reciprocating cylinder head itself is the guide sleeve of the piston rod, the reciprocating cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the reciprocating cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

Do not regularly check the damage of the chrome layer of the reciprocating cylinder: completely extend the reciprocating cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the reciprocating cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the reciprocating cylinder seal. Welding slag is strictly prohibited on the surface of the reciprocating cylinder.

If the reciprocating cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the reciprocating cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow reciprocating cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the reciprocating cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the reciprocating cylinder includes the leakage caused by excessive wear of the reciprocating cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and reciprocating cylinder, and the phenomenon of "pulling the reciprocating cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When installing the reciprocating cylinder pipe, the pipe should be cleaned after installation, and should not pass through the reciprocating cylinder block, and the by-pass pipe must be installed in front of the oil port of the reciprocating cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the reciprocating cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the reciprocating cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about reciprocating cylinder:

What is a differential cylinder?
The differential cylinder is by connecting the return oil of the rod cavity through the pipeline, allowing them to flow into the rodless cavity, thereby speeding up the extension speed of the piston rod. In fact, the cylinder is still the cylinder, but the oil circuit is related to the connection. The oil connection mode in which both chambers of a single rod hydraulic cylinder are fed hydraulic oil is called differential connection.

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
午夜十八禁福利亚洲一区二区| 中国女人日逼免费片| 好嗨哟直播看片在线观看| 强伦人妻一区二区三区视频18| 亚洲成国产人片在线观看| 日本中文字幕无人区一区二区| 人妻波多野结衣爽到喷水| 中国毛茸茸的操逼| 大鸡鸡插我骚逼视频| 国产精品一区二区三区色噜噜| 免费国产香蕉视频在线观看| 男人的天堂日本在线观看| 国产精品白浆一区二区三区| 九九在线视频热线视频精选| 狂野国产性爱av| 日本一区二区不卡在线国产| 日本免费暖暖在线小视频| 性一交一乱一乱一区二区| 欧美一区二区高清视频在线观看| 日韩美女在线视频一区不卡| 哈啊慢点不要了视频| 老头鸡巴操老太骚逼| 91大神精品动漫| 九九视频精品只有这里有| 欧美日韩亚洲人人夜夜澡| 日韩aaa成人免费观看| 天天日天天干天天天天操| 欧美性爱撅臀插入啪啪啪| 亚洲综合一区国产精品| 国产乱子伦视频一区二区三区| 最新日本一区二区三区免费看| 男的鸡巴插女的视频| 大黑屌日本另类肛交| 非洲男生操男生屁眼视频| 男人摸女人下面视频| 男生的小鸡鸡插进女生的桃子 里| 大鸡巴射在穴穴里的视频| 女人被大鸡吧操逼| 欧美丰满大屁股女人的逼被操视频| 嗯嗯嗯啊啊啊好湿好痒好多水视频| 日本入室强伦姧人妻中文|