亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

stacker cylinder Sold to Pakistan

Release time:2023-12-18 10:57:10 Hits: Current position: Home > News

This article mainly introduces:

Pakistan hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

Pakistan stacker cylinder

(Pakistan stacker cylinder,produced by Hengyu Hydraulic Cylinder Factory)

stacker cylinder are widely used in Pakistan,because of clever hydraulic energy conversion,no transmission clearance,powerful torque.So our company has designed stacker cylinder for customers from Pakistan.

Introduction to stacker cylinder:

How to repair the stacker cylinder body when it is damaged: When the stacker cylinder has trace deformation and shallow tensile marks, the stacker cylinder is repaired by strong honing process. The heavy honing process can repair stacker cylinders up to 2.5 times out of tolerance than the original tolerance. It honed the parts with excessive size or shape error through a powerful honing machine, so that the overall size, shape tolerance and roughness of the stacker cylinder can meet the technical requirements.

The assembly work of the stacker cylinder has a great impact on the quality of the stacker cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

There are some honeycomb holes in the inner wall of the stacker cylinder, piston or piston rod surface. How is this formed? When we repair the stacker cylinder, we can see that there are some honeycomb holes on the inner wall of the stacker cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the stacker cylinder is targeted to prevent. Is very necessary.

Do not enter foreign bodies when installing the stacker cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

Answers to some questions about stacker cylinder:

How to set up the one-way cylinder hydraulic system?
Single acting oil cylinder, that is, an oil cylinder with an oil port, can use two three-way valves to control the cylinder action. The three oil ports are respectively connected to P (oil pump), A (oil cylinder), and T (oil tank). If the oil pump is to run continuously, an electromagnetic relief valve can be added. When the cylinder is not moving, the relief valve can unload the oil pump. You can also add a three-way four-way valve, the middle function is unloaded, two outlets: A connected to the fuel tank, B connected to the cylinder.

Two cylinders have a reversing control, if the load of the two cylinders is not the same, how to ensure their synchronization?
The piston rod of the cylinder is required to extend synchronization: install A shunt collector valve or synchronous motor at port A of the direction control valve, and then connect the two outlets of the shunt collector valve to the rod-free cavity of the two cylinders respectively. It is required that the outlet of the diverter collector valve is connected to the rod cavity of the two cylinders respectively when the piston rod is withdrawn in synchronization. The synchronization performance depends on the quality of the diverter valve and the leakage of the hydraulic system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
18岁以下禁看美女的胸| 亚洲 欧美 日韩 主播| 视频一区视频二区制服丝袜| 国产午夜久久精品一区四虎| 亚洲欧美一区二区三区在| 女人扒开腿让我舔十八禁| 色欲精品一区二区三区AV| 中文字幕一区二区三区中文字幕| 中文字幕不卡一区二区免| 国产蜜月精品高清一区二区三区| 女人被大鸡吧操逼| 精品一区二区三区女性色| 国产青青操骚货在线观看| 国产乱精品一区二区三区视频了| 操我骚逼抽插视频| 亚欧日韩国产在线| 亚洲乱熟女一区二区三区| 咪咪爱一级特黄大片| 老太太在丛林日老B| 大黑屌日本另类肛交| 香蕉国产精品偷在线| 中文字幕日韩亚洲| 制服丝袜国产在线第一页| 中日韩中文字幕无码一本| 欧美黑屌操B内射冒白浆| 翘臀小穴在线观看| 亚洲欧美日韩中文v在线| 捆绑调教白浆一区二区三区| 从后面进入嗯啊视频| 亚洲天堂av一区二区在线观看| 加勒比在线不卡一区二区观看| 欧美高清在线观看一区二区三区| 人妻熟女av一区二区三区| 亚洲综合色88综合天堂| 中文字幕在线观一区二区| 中文字幕精品字幕一区二区三区| 97精品人妻人人做人人爽| 久久久久久久久中文字幕| 午夜国产三级一区二区三| 操我骚逼抽插视频| 亚洲美女后入在线播放|