亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

swager cylinder Sold to Peru

Release time:2023-11-09 08:46:15 Hits: Current position: Home > News

This article mainly introduces:

Peru hydraulic cylinder,swager cylinder manufacturer,swager cylinder

Peru swager cylinder

(Peru swager cylinder,produced by Hengyu Hydraulic Co., Ltd)

swager cylinder are widely used in Peru,because of no need for deceleration device,smooth movement,long service life.So our company has designed swager cylinder for customers from Peru.

Introduction to swager cylinder:

If the swager cylinder slips or crawls, please check whether there is astringency inside the swager cylinder, because the internal parts of the swager cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the swager cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the swager cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Factors that should be considered when selecting the oil seal in the swager cylinder: some specific factors should be taken into account when selecting the oil seal in the swager cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: swager cylinder diameter, piston rod diameter, piston rod and piston groove size, swager cylinder working pressure, swager cylinder movement speed, hydraulic system oil temperature and swager cylinder working environment.

When producing oil swager cylinders, there are two processing processes, grinding and rolling, the latter is better than the former. Rolling machining is a kind of non-cutting machining, using the plastic deformation of the metal at room temperature, so that the micro roughness of the workpiece surface is flattened to achieve the purpose of changing the surface structure, mechanical characteristics, shape and size. Therefore, this method can achieve the two purposes of finishing and strengthening at the same time, which can not be done by grinding.

The wear of the hard chromium plating layer of the swager cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

Answers to some questions about swager cylinder:

How to disassemble the cylinder?
Generally speaking, it is not difficult to disassemble the hydraulic cylinder, as long as you are careful, but you often encounter some small trouble in the disassembly process, because the disassembly process is not correct. In fact, this can be avoided, as long as you follow below points. 1. Before removing the hydraulic cylinder, the hydraulic circuit should be relieved of pressure, otherwise, when the oil pipe connected with the cylinder is loosened, the high-pressure oil in the circuit will be rapidly ejected. When the hydraulic pressure comes back, the handwheel or pressure regulating screw at the relief valve should be loosened first, so that the pressure oil is unloaded, and then the power supply or power source is cut off, so that the hydraulic device stops running. 2. Disassembly should prevent damage to the top thread of the piston rod, the oil thread and the chrome layer on the piston rod surface.

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美日韩精品一区丁香| 中文字幕亚洲日韩欧美色| 欧美高清性做爰销魂在线| 国产爽的冒白浆的视频| 久久国产无码模特视频| 国产精品23一区二区| 欧美乱码精品一区二区三区卡| 亚洲欧美日韩国产最新版| 国产精品秘久久久久久| 视频精品在线观看99| 国产成人欧美日本在线观看| 精品一区二区三区日韩| 成人毛片女人18免费片| 蜜臀99久久精品久久久| 人人爽人人爽人人妻av| 午夜精品久久久久久久久久久| 亚洲精品91中文字幕| 在线亚洲专区中文字幕| 国产精品热门在线播放| 那个网站可以看理论片| 久久免费少妇高潮视频| 国产亚洲高清一区二区三区| 国产综合精品久久久久成人蜜臀| 久久久久久久久久福利高潮| 四虎国产精品成人免费久久| 欧美日韩国产精品视频一区| 久久久精品熟女亚洲av麻豆| 成人网站在线进入爽爽爽| 日韩精品视频在线观看一区二区三区| 中国女人free性hd国语| 国产三级网络视频在线观看| 日韩精品一区二区三区四区| 99久久精品国产一区二区三区?| 精品久久久久久红码专区| 韩国午夜理伦三级理论电影| 欧美午夜激情久久久久| 在线电影日韩一区二区三区| 国产99青草视频在线播放视| 欧美日韩一区二区乱码| 亚洲精品夜夜夜妓女网| 91香蕉丝瓜榴莲污污网站|