亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

trunnion cylinder Sold to Mexico

Release time:2023-11-10 08:34:44 Hits: Current position: Home > News

This article mainly introduces:

Mexico hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

Mexico trunnion cylinder

(Mexico trunnion cylinder,produced by Hengyu Hydraulic Cylinder Factory)

trunnion cylinder are widely used in Mexico,because of high work efficiency,no need for deceleration device,clever hydraulic energy conversion.So our company has designed trunnion cylinder for customers from Mexico.

Introduction to trunnion cylinder:

The advantages and disadvantages of the trunnion cylinder: the surface of the trunnion cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the trunnion cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

If the seal of the trunnion cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and trunnion cylinder, and the phenomenon of "pulling the trunnion cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

When the trunnion cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the trunnion cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the trunnion cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

In the case of serious wear on the inner surface of the trunnion cylinder, or when there is a deep longitudinal tensile mark, it should be mapped according to the physical object and re-produced by the professional manufacturer according to the trunnion cylinder manufacturing process for replacement. The trunnion cylinder can also be repaired with TS311 antiwear repair agent. TS311 anti-wear repair agent is mainly used for the repair of worn and slipped metal parts.

Answers to some questions about trunnion cylinder:

How to remove the lifting cylinder from the forklift truck?
The lifting cylinder is generally fixed on the door frame, and there are screws under and above it, and it is OK to loosen the screws with a wrench on the top. However, we must pay attention to ensure safety and prevent damage to the cylinder or safety accidents.

There are four cylinders in the front top of the dump truck. When the second cylinder is lifted to half the height, it suddenly falls back more than 30 cm or so, and the cylinder continues to lift.
The problem is the cylinder, the second section of the different strength of the heart. When the oil supply resistance is small, the first out, when the power is not moving, the cylinder needs to be strong, because the second section needs to pop it out after a while when the pressure is large, the oil can not keep up, so it falls back, and the oil continues to keep up.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
把美女日到高潮喷水视频| 日韩激情精品久久久一区二区| 视频一区视频二区制服丝袜| 女人被躁到高潮嗷嗷叫小| 久久99热东京热亲亲热| 午夜性刺激在线视频免费| 欧美大鸡巴操大骚逼| 美女被插入小穴爆操视频| 尤物性生活午夜在线视频| 国产又粗又猛又色又免费| 国产伦精品一区二区三区视频抖音| 97超级免费视频在线观看| 国产精品久久久69粉嫩| 人妻夜夜添夜夜无码AV| 亚洲精品成a人在线观看| 欧美大胆a级视频 一本| 一区二中文字幕在线看国产一区| 成人男女做爰免费视频网| 中文字幕av一区二区三区哈| 日本免费暖暖在线小视频| 三男狂插小穴穴视频| 男生的小鸡鸡插进女生的桃子 里| 国产精品无码av在线一区| 啊啊啊啊大鸡巴操我视频| 熟女菊蕾老妇俱乐部视频| 国产精品亚洲一区二区三区极品| 国产免费无码一区二区视频无码| 西西大尺度无码免费视频| 色婷婷五月综合久久| 欧美日本大白屁股大黑逼操逼视频| 深插巴西美女的逼| 日本高清不卡一区二区三区| 精品久久久久久不卡亚洲| 蜜臀av一区二区三区免费观| 日本一二区视频在线观看| 女同舔我下面直流水| 胸大裸体美女视频| 日韩素人精品亚洲热一区| 日本 视频 一区二区| 美女的咪咪和骚逼| 日本欧美人一区二区三区|