亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Guatemala

Release time:2023-11-12 14:24:06 Hits: Current position: Home > News

This article mainly introduces:

Guatemala hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Guatemala track steering cylinder

(Guatemala track steering cylinder,produced by Hengyu Hydraulic Cylinder Factory)

track steering cylinder are widely used in Guatemala,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed track steering cylinder for customers from Guatemala.

Introduction to track steering cylinder:

If air enters the hydraulic system, the track steering cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

track steering cylinder body inspection: The inner surface of the track steering cylinder and the piston seal are the main factors causing the leakage in the track steering cylinder, if the track steering cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the track steering cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Classification of track steering cylinder: according to the mode of movement it can be divided into linear reciprocating movement type and rotary swing type; According to the effect of liquid pressure, it can be divided into single acting type and double acting type. According to the structure, it can be divided into piston type, plunger type, multistage telescopic sleeve type, pinion and rack type, etc. According to the installation form can be divided into rod, earring, foot, hinge shaft and so on; According to the pressure grade can be divided into 16Mpa, 25Mpa, 31.5Mpa and so on.

What kind of process is used in the track steering cylinder to make high-quality track steering cylinder products: the body is the main component of the track steering cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The track steering cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the track steering cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the track steering cylinder increases by 25%. If the service life of the track steering cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. track steering cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the track steering cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and track steering cylinder are stuck or the track steering cylinder is blocked. At this time, no matter how to manipulate, the track steering cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the track steering cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about track steering cylinder:

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.

How to limit cylinder push rod rotation?
In general, the push-rod rotation can be limited after the push-rod is connected to the pushed mechanism. For example, the push rod is hinged with the push mechanism, or the push mechanism itself is guided, which can limit the rotation of the push rod.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久久久久久久久久午夜福利| 国产久久久久久久久一区二区| 久久婷婷综合激情亚洲狠狠| 人与嘼一区二区三区| 欧美精品亚洲精品日| 最新99精品视频在线观看| 欧美肉大捧一进一出| 亚洲欧美成人久久一区二区三区| 日本伊人久久精品视频| 亚洲精品电影一区二区三区| 日韩国产av一区二区| 亚洲欧美日韩在线三区| 一本大道av伊人久久综合| 国产精品热门在线播放| 亚洲AV综合色一区二区三区| 亚洲AV永久无码精品加勒比| 亚洲国产日韩一区二区三区| 暗呦交小U女国产精品视频| 东北乱国产对白刺激视频| 亚洲成av一区二区三区| 亚洲精品国自产在线| 亚洲欧美日韩精品在| 人人公开免费看操视频| 91偷自产一区二区三区蜜尹臀| 亚洲线日本一区二区三区| 亚洲国产日韩一区二区三区| 国产麻豆精品福利在线观看| 国产激情老熟女一区二区| 2018在线不卡爱视频| 亚洲AV无码之日韩精品| 国产精品一区二区97| 亚洲欧美日韩精品在| 乱子伦一区二区三区| 亚洲人妻御姐中文字幕| 国产r级亚洲r级在线观看| 波多野结衣人妻奴隶| 日韩欧美一区二区在线播放视频| 亚洲一区二区三区中文字幕手机在线| 国产成人三级一区二区在线观看| 国产精品一区二区久久hs| 国产麻豆精品福利在线观看|