亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

rolling mill cylinder Sold to Republic of Lithuania

Release time:2023-11-12 14:24:29 Hits: Current position: Home > News

This article mainly introduces:

Republic of Lithuania hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

Republic of Lithuania rolling mill cylinder

(Republic of Lithuania rolling mill cylinder,produced by Hengyu Group)

rolling mill cylinder are widely used in Republic of Lithuania,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed rolling mill cylinder for customers from Republic of Lithuania.

Introduction to rolling mill cylinder:

Before the rolling mill cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

rolling mill cylinder body inspection: The inner surface of the rolling mill cylinder and the piston seal are the main factors causing the leakage in the rolling mill cylinder, if the rolling mill cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the rolling mill cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

When installing the rolling mill cylinder pipe, the pipe should be cleaned after installation, and should not pass through the rolling mill cylinder block, and the by-pass pipe must be installed in front of the oil port of the rolling mill cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the rolling mill cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the rolling mill cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

If the rolling mill cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

Answers to some questions about rolling mill cylinder:

Is rubber or polyurethane better for V-ring of hydraulic cylinder?
The hydraulic cylinder V-type seal ring is better with polyurethane, and chlorine rubber is used for various chemicals and high temperatures, especially when there are wear-resistant requirements, polyurethane rubber is needed. But the price of polyurethane rubber is much more expensive than the price of rubber. However, the V-ring material is most commonly used in nitrile and neoprene rubber, and natural rubber is used for sealing water and air. Butyl rubber is used for non-combustible hydraulic fluids and phosphate ester hydraulic fluids. The advantage is that the price is cheaper than the polyurethane material, and the disadvantage is that it is not wear-resistant and the anti-aging property is relatively poor.

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
欧美日韩在线看免费看成人| 亚洲Av无码精品色午夜蜜芽| 国产r级亚洲r级在线观看| 亚洲va久久噜噜噜久久| 国产目拍亚洲精品一区二区| 国产精品亚洲欧美日韩一区在线| 欧美日韩一区二区乱码| 夜鲁夜鲁在线视频维| 韩国爱情电影年轻的母亲| 亚洲欧美成在线观看| 日韩电影av二区久久国产| 中文字幕视频一区人妻| 人与嘼一区二区三区| 亚洲AV综合色一区二区三区| 精品视频一区二区三区美女视频| 国产亚洲黄色在线影院| 中文字幕日韩欧美推理片免费观看| 欧美色欧美亚洲另类在线视频| 国产性夜夜春夜夜爽夜夜| 欧美午夜激情久久久久| 日本色一区二区三区四区五区| 日本电影三级一区二区三区| 午夜影院网站免费观看| 呦男呦女视频精品八区| 亚洲成人久久久久久久| 国产目拍亚洲精品一区二区| 人妻精品一区二区三区| 国产av一区最新精品麻豆| 日本在线观看精品综合| 蜜臀99久久精品久久久| 青青草原精品国产亚洲av| 午夜影院网站免费观看| 国产精品亚洲欧美日韩一区在线| 欧美精品在欧美一区二区三区| 亚洲中文字幕在线视频一区| 国产精品青青青高清在线观看| 人妻熟女的高跟丝袜艳遇| 亚洲中文字幕在线视频一区| 中文字幕熟女一区二区三区| 日韩熟女精品一区二区三区| 最新中文乱码字字幕在线看|