亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic servo cylinder Sold to Turkmenistan

Release time:2023-11-26 09:50:14 Hits: Current position: Home > News

This article mainly introduces:

Turkmenistan hydraulic cylinder,hydraulic servo cylinder manufacturer,hydraulic servo cylinder

Turkmenistan hydraulic servo cylinder

(Turkmenistan hydraulic servo cylinder,produced by Hebei Hengyu company)

hydraulic servo cylinder are widely used in Turkmenistan,because of no transmission clearance,powerful torque,clever hydraulic energy conversion.So our company has designed hydraulic servo cylinder for customers from Turkmenistan.

Introduction to hydraulic servo cylinder:

If it is found that the hydraulic servo cylinder lubrication is poor or the hydraulic servo cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the hydraulic servo cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the hydraulic servo cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the hydraulic servo cylinder center line. In this way, when the piston works in the hydraulic servo cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the hydraulic servo cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

How the cavitation of the hydraulic servo cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the hydraulic servo cylinder, resulting in corrosive damage to the parts.

hydraulic servo cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the hydraulic servo cylinder head itself is the guide sleeve of the piston rod, the hydraulic servo cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the hydraulic servo cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

If the seal of the hydraulic servo cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and hydraulic servo cylinder, and the phenomenon of "pulling the hydraulic servo cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

Answers to some questions about hydraulic servo cylinder:

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

How to calculate the hydraulic cylinder pressure? How much pressure can put up how much weight?
If you want to calculate the pressure of the cylinder, you must know the inner diameter of the cylinder, if the piston rod is needed to lift the weight, it should be: cylinder (no piston rod end) pressure = load (4000N) ÷{(PI /4)X the square of the cylinder diameter (mm) ", it has nothing to do with the piston rod diameter, the rod diameter of the piston rod is only related to the stability of the cylinder. The pressure inside the cylinder should be p=F/S=400×10/(3.14×(0.5×25)×(0.5×25))=8.15MPa which means that you need to provide at least that much pressure to complete the operation.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日本熟妇一区二区三区四区| 看小伙草白女人比的黄片| 中文字幕人妻一区二区三区人妻| 西瓜在线看免费观看视频| 精品一区二区视频在线观看| 国产美女裸体视频全免费| 亚洲乱码专区一区二区三区四区| 精品久久av免费一区二区三区| 日本黑鸡吧黄色录像| 国产精品三二一免费| 日日狠狠久久888av| 天美传媒精品1区2区3区| 亚洲综合色88综合天堂| 男人吃奶大鸡巴操逼视频| 使劲操大骚逼av| 大鸡扒干美女BB直流水| 中文字幕欧美人妻在线| 日韩精品无码一区二区三区不卡| 美女大鸡操很多水在线看| 九九视频精品只有这里有| 成人av大全免费一区二区三区| 美女穿黑丝被大鸡巴猛操| 美女麻豆颜色光屁股眼子| 操的我的逼逼好爽好多水| 精品久久久久亚洲中文字幕| 午夜国产三级一区二区三| 在线视频观看一区| 亚洲v国产v天堂a无码| 91秦先生全集在线观看| 美女大鸡操很多水在线看| 美女大鸡操很多水在线看| 白嫩在线亚洲观看| 最新中文字幕av不卡高清| 国产女明星一级毛片| 大鸡巴射精在小穴动漫版| 男人的天堂久久久久久久| 一区二区在线不卡| 97人人澡人人爽人人揉| 精品人妻少妇一区二区三区不卡| 亚洲一区二区三区四区国产| 99精品一级欧美片免费|