亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Cote d 'Ivoire

Release time:2023-11-27 15:08:49 Hits: Current position: Home > News

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Cote d 'Ivoire servo cylinder

(Cote d 'Ivoire servo cylinder,produced by Hengyu Hydraulic Co., Ltd)

servo cylinder are widely used in Cote d 'Ivoire,because of long service life,smooth movement,high work efficiency.So our company has designed servo cylinder for customers from Cote d 'Ivoire.

Introduction to servo cylinder:

The servo cylinder should be vented: when the servo cylinder is installed or parked for a long time to work again, the air will penetrate into the servo cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the servo cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the servo cylinder, the oil is best entered and discharged from the highest point of the servo cylinder. servo cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

If the piston rod and servo cylinder are stuck or the servo cylinder is blocked, at this time, no matter how to operate, the servo cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the servo cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

servo cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

servo cylinder can not drive the load troubleshooting: oil pressure is too low. servo cylinder selection specifications are too small. Leakage in servo cylinder or associated hydraulic system element.

Answers to some questions about servo cylinder:

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久精品一本无码免费| 久久精品国产亚洲高清| 久久99亚洲精品视频| 日韩激情av一区二区| 一区二区三区精品99久久| 日本一区二区三区影院| 99国产精品一区二区三区| 国产在线一区二区三区欧美| 亚洲国产精品无码久久久高潮| 国产亚洲综合欧美一区| 夫妇交换性4中文字幕无码| 国产性生活视频免费| 在线播放亚洲欧美日韩| 91香蕉下载并安装| 日韩精品一区二区三区高清免费| 经典国产乱子伦精品| 欧美日韩国产综合在线视频| 国产性生活视频免费| 日本视频免费一区二区| 欧美日韩一区二区在线不卡| 一区二区三区四区欧美日韩亚洲| 日本一区二区三区免费的视频| 一区二区三区精品99久久| 激情小说校园春色亚洲| 国产白丝theporn| 亚洲国产精品无码av| 久久精品成人免费国产| 日韩亚洲欧美综合在线| 欧美日韩一区二区三区大片在线观看| 日本无人区一区二区三区| 中文字幕亚洲一区巨区| 免费人成视频在线观看不卡| 国产白嫩精品久久久| 亚洲欧美中文在线另类| 中文字幕亚洲日韩欧美色| 四虎成人精品一区二区| 久久熟女av一区二区三区| 精品视频亚洲一区二区三区| 国产一区二区精品久| 国产资源网中文最新版| 91精品无码中文字幕在线|