亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

track steering cylinder Sold to Burma

Release time:2023-11-09 08:46:19 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

Burma track steering cylinder

(Burma track steering cylinder,produced by Hebei Hengyu company)

track steering cylinder are widely used in Burma,because of clever hydraulic energy conversion,simple structure and reliable operation,excellent temperature resistance.So our company has designed track steering cylinder for customers from Burma.

Introduction to track steering cylinder:

track steering cylinder spool stuck or valve hole blocked How to solve: When the flow valve or direction valve spool stuck or valve hole blocked, the track steering cylinder prone to misoperation or action failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium.

When installing the track steering cylinder, the axial ends of the track steering cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the track steering cylinder, there is axial expansion. If the two ends of the track steering cylinder are fixed, all parts of the track steering cylinder will be deformed. When disassembling the track steering cylinder, it is strictly forbidden to hammer the track steering cylinder and the piston surface, such as the track steering cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

When the track steering cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the track steering cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the track steering cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Answers to some questions about track steering cylinder:

Cylinder pressure calculation formula
The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate it according to the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the working pressure P (unit MPa) the thrust of the cylinder F push =3.14*R*R*P (unit N) The pulling force of the cylinder F pull =3.14* (R*R-r* R) *P (unit N).

How do hydraulic equipment and hydraulic cylinders maintain a certain pressure after pressing to a certain position?
There are several methods. 1. You can use a constant pressure variable pump to adjust the control pressure of the pump to the pressure required by the cylinder, so that when the cylinder is in place, the pump uses the minimum flow rate to maintain the pressure, and the system is more energy saving. 2. If the pressure is maintained for a short time, a hydraulic control check valve can be added to the oil inlet end of the cylinder to close the cylinder and maintain the pressure. If the volume of the cylinder is large, an accumulator can be added between the valve and the cylinder to maintain pressure for 10-30 minutes. 3. You can add a small flow pump, the large pump after unloading, the small pump has been running, specifically for maintaining pressure.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
国产日韩欧美老人啪啪| 亚洲欧美日韩在线三区| 99久久国产亚洲精品美女| av毛片在线免费观看| 国内自拍2019在线| 91精品无码中文字幕在线| 2021国产三级精品三级在专区| 国产白丝一区二区三区| 91久久久久久久国产| 欧美日韩一区二区三区自拍| 国产v片在线免费观看| 国产视频网站在线不卡| 国产精品秘久久久久久| 国产精品国产三级av| 国产精品久久小视频| 在线亚洲专区中文字幕| 婷婷色婷婷开心五月四房播播| 亚洲精品夜夜夜妓女网| 欧美日韩国产综合在线视频| 国产三级在线免费播放| 蜜臀99久久精品久久久| 午夜福利国产观看视频1| 国产又长有粗的视频| 国产精品日本女优在线观看| 欧美高清手机一区二区| 苍井空一区二区三区在线观看| 国产精品v欧美精品v日本精| 欧美国产日韩精品77上位| 9久久99久久久免费精品然| 亚洲精品电影一区二区三区| 神马午夜久久久久久| 中文字幕人妻女同一区| 久久久久久亚洲一区二区| 国产精品久久久久一区二区三区厕所| 色欲香天天综合免费区一区二| 亚洲天堂网2020| 亚洲av成人精品日韩一区麻豆| 97在线视频播放免费观看不卡| 91香蕉在线观看影视| 国产三级视频在线观看网站| 2021国产三级精品三级在专区|