亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

500 ton hydraulic cylinder Sold to The Philippines

Release time:2023-11-12 15:26:17 Hits: Current position: Home > News

This article mainly introduces:

The Philippines hydraulic cylinder,500 ton hydraulic cylinder manufacturer,500 ton hydraulic cylinder

The Philippines 500 ton hydraulic cylinder

(The Philippines 500 ton hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

500 ton hydraulic cylinder are widely used in The Philippines,because of no need for deceleration device,long service life,smooth movement.So our company has designed 500 ton hydraulic cylinder for customers from The Philippines.

Introduction to 500 ton hydraulic cylinder:

The 500 ton hydraulic cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the 500 ton hydraulic cylinder, bite. Elimination method: When installing the 500 ton hydraulic cylinder, ensure that the axis position of the 500 ton hydraulic cylinder is consistent with the direction of movement; Make the load borne by the 500 ton hydraulic cylinder as far as possible through the 500 ton hydraulic cylinder axis, to avoid the phenomenon of eccentricity.

500 ton hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the 500 ton hydraulic cylinder head itself is the guide sleeve of the piston rod, the 500 ton hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the 500 ton hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

If the 500 ton hydraulic cylinder slips or crawls, please check whether there is astringency inside the 500 ton hydraulic cylinder, because the internal parts of the 500 ton hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the 500 ton hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the 500 ton hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

The definition of the minimum stable speed refers to the minimum movement speed of the 500 ton hydraulic cylinder without crawling phenomenon when the full load is moving, it has no uniform indicator, and the 500 ton hydraulic cylinder that undertakes different work has different requirements for the minimum stable speed.

Answers to some questions about 500 ton hydraulic cylinder:

What is the safety factor of 25MPa cylinder wall thickness?
Safety factor n can take 3 cylinder material allowable stress [s]=sb/n δ/D=0.08 ~ 0.3 cylinder wall thickness δ=PMAX*D/ (2.3[s]-3PMAX) δ/D≤0.08 cylinder wall thickness δ=PMAX*D/2[s] P < 16MPa, Pmax=1.5Pn; P > 16MPa, Pmax=1.25Pn cold-drawn tube or honing tube is better!

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
久久久国产系列丝袜熟女| 色欲精品一区二区三区AV| 精彩欧美一区二区三区| 成人刺激性视频在线观看| 中文字幕乱码人妻一区二区三区| 高清无码精品一区二区三区| 联系附近成熟妇女| 美女骚逼被操出白浆| 亚洲女同一区二区三久久精品| 男插女下面高潮视频| 淫荡淫水逼操烂视频| 久久免费国产视频| 国产日韩一区二区三区在线播放| 国产一区二区三区三级88| 大鸡巴猛插小穴视频| 激情亚洲人妻精品| 日本欧美一区二区三区| 男生插女生下面流出白色精液视频| 美女被插进去黄色| 国产 日韩 亚洲 一区| 久久丁香花五月天色婷婷| 一区二区国产欧美日韩无| 欧美日韩精品视频在线第一区| 中文字幕你懂的av一区二区| 女人的骚逼免费视频| 国产一区二区三区午夜精品久久| 99热这里只有精品97| 又色又爽又黄的吃奶Av| 在线免费观看一区| 美女裸胸屁股视频| 久久精品男人的天堂av| 鸡巴操美女小穴羞羞视频| 亚洲一区二区女同性恋免费看| 97超视频免费在线观看| 色哟哟精品视频一区二区| 五月天国产成人免费视频| 欧美亚洲综合一区二区三区| 国产精品视频一区二区三区分享| 天天躁久久躁中文字字幕| 色欲色欲色视频综合| 一级毛片完整版免费播放一区|